Cisco 350-401 Quiz 52 Topic 8 Questions 256-260

Question: 1

Refer to the exhibit.

q1_350-401

A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are made, the port channel does not establish. Based on the configuration excerpt of SW3. what is the cause of the problem?

AThe port-channel trunk is not allowing the native VLAN

BThe port channel on SW2 is using an incompatible protocol.

CThe port-channel mode should be set to auto.

DThe port-channel interface load balance should be set to src-mac

Show Answer

Question: 2

Refer to the exhibit.

q2_350-401

Refer to the exhibit. An engineer is using XML in an application to send information to a RESTCONF-enabled device. After sending the request, the engineer gets this response message and a HTTP response code of 400. What do these responses tell the engineer?

AThe Accept header sent was application/xml

BPOST was used instead of PUT to update

CThe Content-Type header sent was application/xml.

DJSON body was used

Show Answer

Question: 3

Refer to the exhibit.

q3_350-401

Refer to the exhibit. What does the error message relay to the administrator who is trying to configure a Cisco IOS device?

AA NETCONF request was made for a data model that does not exist.

BThe device received a valid NETCONF request and serviced it without error.

CA NETCONF message with valid content based on the YANG data models was made, but the request failed.

DThe NETCONF running datastore is currently locked.

Show Answer

Question: 4

Refer to the exhibit.

q4_350-401

Refer to the exhibit. R1 is able to ping the R3 fa0/1 interface. Why do the extended pings fail?

AThe maximum packet size accepted by the command is 1476 bytes.

BR3 is missing a return route to 10.99.69.0/30

CR2 and R3 do not have an OSPF adjacency

DThe DF bit has been set

Show Answer

Question: 5

Refer to the exhibit.

q5_350-401

Which IP address becomes the next active next hop for 192.168.102 0/24 when 192.168.101.2 fails?

A192.168.101.18

B192.168.101.6

C192.168.101.10

D192.168.101.14

Show Answer

Refer to the exhibit.
A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are made, the port channel does not establish. Based on the configuration excerpt of SW3. what is the cause of the problem?

Refer to the exhibit.
Refer to the exhibit. An engineer is using XML in an application to send information to a RESTCONF-enabled device. After sending the request, the engineer gets this response message and a HTTP response code of 400. What do these responses tell the engineer?

Refer to the exhibit.
Refer to the exhibit. What does the error message relay to the administrator who is trying to configure a Cisco IOS device?

Refer to the exhibit.
Refer to the exhibit. R1 is able to ping the R3 fa0/1 interface. Why do the extended pings fail?

Refer to the exhibit.
Which IP address becomes the next active next hop for 192.168.102 0/24 when 192.168.101.2 fails?

Cisco 350-401 Quiz:52 Topic:8 Questions:256-260

Refer to the exhibit.A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are made, the port channel does not establish. Based on the configuration excerpt of SW3. what is the cause of the problem?

Refer to the exhibit.Refer to the exhibit. An engineer is using XML in an application to send information to a RESTCONF-enabled device. After sending the request, the engineer gets this response message and a HTTP response code of 400. What do these responses tell the engineer?

Refer to the exhibit.Refer to the exhibit. What does the error message relay to the administrator who is trying to configure a Cisco IOS device?

Refer to the exhibit.Refer to the exhibit. R1 is able to ping the R3 fa0/1 interface. Why do the extended pings fail?

Refer to the exhibit.Which IP address becomes the next active next hop for 192.168.102 0/24 when 192.168.101.2 fails?

Cisco 350-401 Quiz:52 Topic:8 Questions:256-260

Refer to the exhibit.
A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are made, the port channel does not establish. Based on the configuration excerpt of SW3. what is the cause of the problem?

Refer to the exhibit.
Refer to the exhibit. An engineer is using XML in an application to send information to a RESTCONF-enabled device. After sending the request, the engineer gets this response message and a HTTP response code of 400. What do these responses tell the engineer?

Refer to the exhibit.
Refer to the exhibit. What does the error message relay to the administrator who is trying to configure a Cisco IOS device?

Refer to the exhibit.
Refer to the exhibit. R1 is able to ping the R3 fa0/1 interface. Why do the extended pings fail?

Refer to the exhibit.
Which IP address becomes the next active next hop for 192.168.102 0/24 when 192.168.101.2 fails?