Cisco 350-401 Quiz 53 Topic 2 Questions 261-265

Question: 1

Refer to the exhibit.

q1_350-401

Refer to the exhibit. An engineer configures CoPP and enters the show command to verify the implementation. What is the result of the configuration?

AAll traffic will be policed based on access-list 120.

BIf traffic exceeds the specified rate, it will be transmitted and remarked.

CClass-default traffic will be dropped.

DICMP will be denied based on this configuration.

Show Answer

Question: 2

Refer to the exhibit.

q2_350-401

Refer to the exhibit. Which two commands are needed to allow for full reachability between AS 1000 and AS 2000? (Choose two)

AR1#network 19.168.0.0 mask 255.255.0.0

BR2#no network 10.0.0.0 255.255.255.0

CR2#network 19.168.0.0 mask 255.255.0.0

DR2#network 209.165.201.0 mask 255.255.192.0

ER1#no network 10.0.0.0 255.255.255.0

Show Answer

Question: 3

Refer to the exhibit.

q3_350-401

Refer to the exhibit. A network engineer configures a GRE tunnel and enters the show Interface tunnel command. What does the output confirm about the configuration?

AThe keepalive value is modified from the default value.

BInterface tracking is configured.

CThe tunnel mode is set to the default.

DThe physical interface MTU is 1476 bytes.

Show Answer

Question: 4

Refer to the exhibit.

q4_350-401

Refer to the exhibit. PC-1 must access the web server on port 8080. To allow this traffic, which statement must be added to an access control list that is applied on SW2 port G0/0 in the inbound direction?

Apermit host 172.16.0.2 host 192.168.0.5 eq 8080

Bpermit host 192.168.0.5 host 172.16.0.2 eq 8080

Cpermit host 192.168.0.5 eq 8080 host 172.16.0.2

Dpermit host 192.168.0.5 it 8080 host 172.16.0.2

Show Answer

Question: 5

Which behavior can be expected when the HSRP version is changed from 1 to 2?

AEach HSRP group reinitializes because the virtual MAC address has changed

BNo changes occur because version 1 and 2 use the same virtual MAC OUI.

CNo changes occur because the standby router is upgraded before the active router.

DEach HSRP group reinitializes because the multicast address has changed

Show Answer

Refer to the exhibit.
Refer to the exhibit. An engineer configures CoPP and enters the show command to verify the implementation. What is the result of the configuration?

Refer to the exhibit.
Refer to the exhibit. Which two commands are needed to allow for full reachability between AS 1000 and AS 2000? (Choose two)

Refer to the exhibit.
Refer to the exhibit. A network engineer configures a GRE tunnel and enters the show Interface tunnel command. What does the output confirm about the configuration?

Refer to the exhibit.
Refer to the exhibit. PC-1 must access the web server on port 8080. To allow this traffic, which statement must be added to an access control list that is applied on SW2 port G0/0 in the inbound direction?

Which behavior can be expected when the HSRP version is changed from 1 to 2?

Cisco 350-401 Quiz:53 Topic:2 Questions:261-265

Refer to the exhibit.Refer to the exhibit. An engineer configures CoPP and enters the show command to verify the implementation. What is the result of the configuration?

Refer to the exhibit.Refer to the exhibit. Which two commands are needed to allow for full reachability between AS 1000 and AS 2000? (Choose two)

Refer to the exhibit.Refer to the exhibit. A network engineer configures a GRE tunnel and enters the show Interface tunnel command. What does the output confirm about the configuration?

Refer to the exhibit.Refer to the exhibit. PC-1 must access the web server on port 8080. To allow this traffic, which statement must be added to an access control list that is applied on SW2 port G0/0 in the inbound direction?

Which behavior can be expected when the HSRP version is changed from 1 to 2?

Cisco 350-401 Quiz:53 Topic:2 Questions:261-265

Refer to the exhibit.
Refer to the exhibit. An engineer configures CoPP and enters the show command to verify the implementation. What is the result of the configuration?

Refer to the exhibit.
Refer to the exhibit. Which two commands are needed to allow for full reachability between AS 1000 and AS 2000? (Choose two)

Refer to the exhibit.
Refer to the exhibit. A network engineer configures a GRE tunnel and enters the show Interface tunnel command. What does the output confirm about the configuration?

Refer to the exhibit.
Refer to the exhibit. PC-1 must access the web server on port 8080. To allow this traffic, which statement must be added to an access control list that is applied on SW2 port G0/0 in the inbound direction?