Cisco 200-301 Quiz 15 Topic 10 Questions 71-75

Question: 1

Refer to the exhibit.

q1_200-301

An extended ACL has been configured and applied to router R2 The configuration farted to work as intended Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0 20 026 from the 10.0.10 0/26 subnet while still allowing all other traffic? (Choose two)

AAdd a 'permit ip any any' statement to the begining of ACL 101 for allowed traffic.

BAdd a 'permit ip any any' statement at the end of ACL 101 for allowed traffic

CThe source and destination IPs must be swapped in ACL 101

DThe ACL must be configured the Gi0/2 interface inbound on R1

EThe ACL must be moved to the Gi0/1 interface outbound on R2

Show Answer

Question: 2

Which two capacities of Cisco DNA Center make it more extensible? (Choose two)

Aadapters that support all families of Cisco IOS software

BSDKs that support interaction with third-party network equipment

Ccustomized versions for small, medium, and large enterprises

DREST APIs that allow for external applications to interact natively with Cisco DNA Center

Emodular design that is upgradable as needed

Show Answer

Question: 3

Which IPv6 address type provides communication between subnets and cannot route on the Internet?

Aglobal unicast

Bunique local

Clink-local

Dmulticast

Show Answer

Question: 4

Refer to the Exhibit.

q4_200-301

68

79

After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1. which error must be corrected?

AThere is a native VLAN mismatch

BAccess mode is configured on the switch ports.

CThe PCs are m the incorrect VLAN

DAll VLANs are not enabled on the trunk

Show Answer

Question: 5

What occurs when PortFast is enabled on an interface that is connected to another switch?

ASpanning tree may fail to detect a switching loop in the network that causes broadcast storms

BVTP is allowed to propagate VLAN configuration information from switch to switch automatically.

CRoot port choice and spanning tree recalculation are accelerated when a switch link goes down

DAfter spanning tree converges PortFast shuts down any port that receives BPDUs.

Show Answer

Refer to the exhibit.
An extended ACL has been configured and applied to router R2 The configuration farted to work as intended Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0 20 026 from the 10.0.10 0/26 subnet while still allowing all other traffic? (Choose two)

Which two capacities of Cisco DNA Center make it more extensible? (Choose two)

Which IPv6 address type provides communication between subnets and cannot route on the Internet?

Refer to the Exhibit.
68
79
After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1. which error must be corrected?

What occurs when PortFast is enabled on an interface that is connected to another switch?

Cisco 200-301 Quiz:15 Topic:10 Questions:71-75

Refer to the exhibit.An extended ACL has been configured and applied to router R2 The configuration farted to work as intended Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0 20 026 from the 10.0.10 0/26 subnet while still allowing all other traffic? (Choose two)

Which two capacities of Cisco DNA Center make it more extensible? (Choose two)

Which IPv6 address type provides communication between subnets and cannot route on the Internet?

Refer to the Exhibit.6879After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1. which error must be corrected?

What occurs when PortFast is enabled on an interface that is connected to another switch?

Cisco 200-301 Quiz:15 Topic:10 Questions:71-75

Refer to the exhibit.
An extended ACL has been configured and applied to router R2 The configuration farted to work as intended Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0 20 026 from the 10.0.10 0/26 subnet while still allowing all other traffic? (Choose two)

Refer to the Exhibit.
68
79
After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1. which error must be corrected?