Huawei H12-211 Quiz 59 Topic 7 Questions 291-295

Question: 1

Refer to the grapic. An administrator has configured RIPv2 on the two routers, following which he implements the command silent-interface s0/0/1 on RTA. What effect will this command have on the network? (Two Answers)

ARTA will continue to learn routes from RTB

BRTB will continue to learn routes from RTA

CRTA will have no neighbor relationship with RTB

DRTB will have no adjacency relationship with RTA

Show Answer

Question: 2

Refer to the graphic. R1, R2 and R3 are running RIPv1. R1 and R3 both advertise 172.16.0.0 to the RIP network. How will this affect R2?

AR2 will not have a route to the networks 172.16.1.0/24 and 172.16.2.0/24

BR2 will only have a route to 172.16.1.0/24

CR2 will only have a route to 172.16.2.0/24

DR2 will have a route to both networks 172.16.1.0/24 and 172.16.2.0/24, but some packets for these destinations will be lost.

Show Answer

Question: 3

debugging rip 1

Sep 13 2013 11:07:20.974.1-05:13 R2 RIP/7/DBG: 6: 13414: RIP 1: Receiving v1 response on

GigabitEthernet0/0/0 from 10.0.12.1 with 1 RTE

Sep 13 2013 11:07:20.974.2-05:13 R2 RIP/7/DBG: 6: 13465: RIP 1: Receive response from 10.0.12.1 on

GigabitEthernet0/0/0

Sep 13 2013 11:07:20.974.3-05:13 R2 RIP/7/DBG: 6: 13476: Packet: Version 1, Cmd response, Length 24

Sep 13 2013 11:07:20.974.4-05:13 R2 RIP/7/DBG: 6: 13527: Dest 1.0.0.0, Cost 1

Sep 13 2013 11:07:20.974.5-05:13 R2 RIP/7/DBG: 6: 2688: RIP 1: Ignoring packet. This version is not configured.

Refer to the debug output. Following configuration of R2, the administrator discovers that the behavior is not as expected and performs debugging. Based on the output from the debug, what is the source of the problem?

AR2 has configured an ACL to block the route to network 1.0.0.0

BR2 has enabled split horizon.

CR1 is using authentication, however R2 is not.

DR2 is operating using RIPv2, while R1 is using RIPv1.

Show Answer

Question: 4

Refer to the graphic. An administrator has configed RIPv2 in the two routers shows in the figure. What will happen after configuring the following commands? (Choose two)

[RTA-Serial0/0/1]rip output

[RTA-rip-1]silent-interface s0/0/1

ARTA will have the route learned from the RTB

BRTB will have the route learn from the RTA

CRTA will have no neighbor relationship with RTB

DRTB will have no neighbor relationship with RTB

Show Answer

Question: 5

Which of the following statements about a designated port working in RIPv2 multicast mode are true? (Choose three)

AThe port receives only RIPv2 multicast packets.

BThe port does not receive RIPv1 broadcast packets.

CThe port does not receive RIPv2 broadcast packets.

DThe port receives only RIPv1 multicast packets.

Show Answer

Huawei H12-211 Quiz:59 Topic:7 Questions:291-295