Cisco 300-435 Quiz 3 Topic 10 Questions 11-15

Question: 1

Refer to the exhibit. End users cannot connect to the circular network, and the signal strength is poor. A missing or unknown APN status message is present and the modern status remains in low-power mode. Which addresses the issue?

AUse the device/celluiar/status vManage resource URI to ensure sufficient radio signal strength.

BUse the systen/device/controllers vManage resource URI to set the platform temperature.

CUse the device/app-route/statistics vManage resource URI to allow packets reachability to hosts.

DUse the device/tools'ping vManage resource URI to allow network device reachability.

Show Answer

Question: 2

Refer to the exhibit.

q2_300-435

Cisco SD-WAN deployment must be fixed using vManage APIs. A call to vEdge Hardware

Health API returns the data in the exhibit (only a portion is shown). If the JSON shown in the exhibit is

converted to a Python dictionary named ''d'', how is the ''status'' property referenced?

Ad['data']['statusList']['status']

Bnbvnbvvnbhg

Cd{'data'}[0]{'statusList'}[0]{'status'}

Dd[data][0][statusList][0][status]

Show Answer

Question: 3

D18912E1457D5D1DDCBD40AB3BF70D5D

Refer to the exhibit.

q3_300-435

The configuration commands are entered in CLI config mode to configure a static telemetry

subscription on a Cisco IOS XE device. The commands are accepted by the device, but the consumer receives

no telemetry dat

a. Which change must be made to ensure that the consumer receives the telemetry data?

AThe IP address of the receiver must be set.

BThe stream type must be set to YANG.

CThe update policy period must be shortened.

DThe sender IP address must be set.

Show Answer

Question: 4

Refer to the exhibit.

q4_300-435

Which interface is included in the payload resulting from the script?

Aethernet 1

Bethernet 100

Cethernet 1/1

Dethernet 0

Show Answer

Question: 5

Refer to the exhibit. Interfaces named Loopback0, Loopback1, and Loopback2 must be created and enabled on a Cisco IOS XE target device in the lab group. Which loop must be added to the end of the Ansible ''create int'' task?

Awith_items: ''{{intlist}}''

Bwith_parent: ''{{intlist}}''

Cwith_list: ''{{intlist}}''

Dwith_groups: ''{{intlist}}''

Show Answer

Refer to the exhibit. End users cannot connect to the circular network, and the signal strength is poor. A missing or unknown APN status message is present and the modern status remains in low-power mode. Which addresses the issue?

Refer to the exhibit.
Cisco SD-WAN deployment must be fixed using vManage APIs. A call to vEdge Hardware
Health API returns the data in the exhibit (only a portion is shown). If the JSON shown in the exhibit is
converted to a Python dictionary named ''d'', how is the ''status'' property referenced?

Refer to the exhibit.
Which interface is included in the payload resulting from the script?

Refer to the exhibit. Interfaces named Loopback0, Loopback1, and Loopback2 must be created and enabled on a Cisco IOS XE target device in the lab group. Which loop must be added to the end of the Ansible ''create int'' task?

Cisco 300-435 Quiz:3 Topic:10 Questions:11-15

Refer to the exhibit. End users cannot connect to the circular network, and the signal strength is poor. A missing or unknown APN status message is present and the modern status remains in low-power mode. Which addresses the issue?

Refer to the exhibit.Cisco SD-WAN deployment must be fixed using vManage APIs. A call to vEdge HardwareHealth API returns the data in the exhibit (only a portion is shown). If the JSON shown in the exhibit isconverted to a Python dictionary named ''d'', how is the ''status'' property referenced?

Refer to the exhibit.Which interface is included in the payload resulting from the script?

Refer to the exhibit. Interfaces named Loopback0, Loopback1, and Loopback2 must be created and enabled on a Cisco IOS XE target device in the lab group. Which loop must be added to the end of the Ansible ''create int'' task?

Cisco 300-435 Quiz:3 Topic:10 Questions:11-15

Refer to the exhibit.
Cisco SD-WAN deployment must be fixed using vManage APIs. A call to vEdge Hardware
Health API returns the data in the exhibit (only a portion is shown). If the JSON shown in the exhibit is
converted to a Python dictionary named ''d'', how is the ''status'' property referenced?

Refer to the exhibit.
Which interface is included in the payload resulting from the script?